ADB Over Wireless


Answer :

Rooting is not required. With USB cable connected, port 5555 opened across all involved firewalls and debug mode enabled

adb tcpip 5555

then look into wireless properties of your device and the network you use, to see which IP address have been granted to device (or configure your DHCP always to use the same for the device mac address). Then

adb connect 192.168.1.133

(were 192.168.1.133 is a sample IP address).

This is all. You can now use adb shell or adb install or adb upload or the like with USB cable plugged out.

To switch back to USB mode, 

adb usb

The device may also revert back to USB mode after reboot.

This mode is needed for development of applications that use attached USB devices directly (USB port is used by device so cannot be used by ADB). It is briefly covered in the USB debugging section of the Android website.


I ran into the same problem today and find that things are fine on my non-rooted 4.2 Galaxy Nexus device, but does not work on my older (again non-rooted) Samsung Galaxy Y (2.3) device.

I tried the steps given here but looks like one needs a rooted phone to work on some of the earlier models (and maybe other non-nexus devices too).

This is what I tried -

$ adb shell netstat | grep 5555

No socket was opened on this port.

Tried to manually set the steps that adb tcpip does -

$ adb shell setprop service.adb.tcp.port 5555 $ adb shell stop adbd $ adb shell start adbd $ adb shell getprop | grep adb

This does not show the property that was just set.

This is what it shows on my nexus device where it works without rooting -

$ adb shell getprop | grep adb [service.adb.tcp.port]: [5555]

So depending on what phone/OS version u have, your mileage might vary.

:-)


For wireless adb on my Nexus 4 @ Android 4.4.2 (Kitkat) I usually do:

  1. Turn on usb debug in 'Developer options'
  2. Connect via usb cable, accept an RSA key dialog
  3. adb tcpip 5555
  4. adb connect 192.168.?.? (device IP on local wlan)

  5. Disconnect usb cable

  6. Test if connection is still on: adb devices

    • If ok you'll see:
      List of devices attached
      192.168.?.?:5555 device
    • Else use Kumar's method:
      https://stackoverflow.com/a/14855490/818634

Comments

Post a Comment

Popular posts from this blog

Converting A String To Int In Groovy

Answer : Use the toInteger() method to convert a String to an Integer , e.g. int value = "99".toInteger() An alternative, which avoids using a deprecated method (see below) is int value = "66" as Integer If you need to check whether the String can be converted before performing the conversion, use String number = "66" if (number.isInteger()) { int value = number as Integer } Deprecation Update In recent versions of Groovy one of the toInteger() methods has been deprecated. The following is taken from org.codehaus.groovy.runtime.StringGroovyMethods in Groovy 2.4.4 /** * Parse a CharSequence into an Integer * * @param self a CharSequence * @return an Integer * @since 1.8.2 */ public static Integer toInteger(CharSequence self) { return Integer.valueOf(self.toString().trim()); } /** * @deprecated Use the CharSequence version * @see #toInteger(CharSequence) */ @Deprecated public static Integer toInteger(String self) { return toInteg
Read more

"Cannot Create Cache Directory /home//.composer/cache/repo/https---packagist.org/, Or Directory Is Not Writable. Proceeding Without Cache"

Answer : if anyone pass through here, this is shorter solution: sudo chown -R $USER $HOME/.composer it seems to me the group information is missing in your command sudo chown -R <user> /home/<user>/.composer/cache/repo/https---packagist.org Shoud be sudo chown -R <user>:<group> /home/<user>/.composer/cache/repo/https---packagist.org But to avoid other permission issues, I would rather advise: sudo chown -R <user>:<group> /home/<user>/.composer/cache (you'll need access to other folders in there) and sudo chown <user>:<group> /home/<user>/.composer To make sure your user has permissions enough on the global composer folder. Mind the missing recursion so the user don't own keys created by root. If you need to find out the group: groups <user>
Read more

Android How Can I Convert A String To A Editable

Answer : As you probably found out, Editable is an interface so you cannot call new Editable() . However an Editable is nothing more than a String with Spannables, so use SpannableStringBuilder: Editable editable = new SpannableStringBuilder("Pass a string here"); If you only want to change the Spannables, never the text itself, you can use a basic SpannableString. Use Editable.Factory.getInstance().newEditable(str) From the android documentation: Returns a new SpannedStringBuilder from the specified CharSequence. You can override this to provide a different kind of Spanned.
Read more